Brake disc and caliper on a car before its MOT, checked by a Kent mobile mechanic

What Brake Faults Fail an MOT?

October 24, 2026

Written by Petro Olekhnovych, mobile mechanic in Aylesham, Kent

Quick answerThe brake faults that most often fail an MOT are worn pads, discs that are excessively worn or damaged, poor braking performance or imbalance between wheels on the roller test, a weak handbrake, corroded pipes or damaged hoses, fluid leaks and brake or ABS warning lights. Faults are graded minor, major or dangerous. Most can be spotted at a pre-MOT check.

How brakes are tested at the MOT

The tester checks your brakes in two ways. First, a visual inspection of what can be seen: pads, discs, pipes, hoses, cables and the pedal. Second, a performance test, usually on a roller brake tester, which measures how hard each wheel brakes and compares the two sides.

The MOT inspection manual sets out what counts as a failure. Each defect is graded:

  • Minor: recorded, but the car still passes
  • Major: the car fails and must be repaired
  • Dangerous: the car fails and must not be driven until repaired

Pad and disc faults

  • Pads worn down to the wear indicator or below the minimum lining thickness
  • Pads missing or fitted incorrectly
  • Pads or discs contaminated with oil, grease or brake fluid
  • Discs excessively worn, deeply scored, cracked or insecure

A lip on the edge of the disc is normal and not a fail in itself. What matters is how worn the braking surface is. Our guide to lipped and scored brake discs explains the difference, and we cover measurement in brake disc minimum thickness.

Want to pass your MOT first time?

We do pre-MOT checks and fix advisories at your home or work across East Kent.

WhatsApp for a free quote Call 07563 350335 Contact form

Labour £30 to £50 per hour depending on the job. Send your reg number and we will reply with a price before any work starts.

Performance and imbalance

On the roller tester the brakes have to reach a minimum efficiency compared with the weight of the car. The tester also checks for imbalance across an axle. If one wheel brakes much harder than the other, the car will pull under braking and fails.

Imbalance is very often caused by a sticking caliper or seized slide pins, a problem made worse by Kent winters and road salt. Other performance faults include:

  • Brakes binding or dragging when released
  • Excessive fluctuation, which points to a warped disc or oval drum
  • A handbrake that does not hold well enough, often from seized cables or rear calipers on cars that sit unused

Pipes, hoses and leaks

Underneath, the tester looks closely at:

  • Steel brake pipes that are corroded, damaged or poorly secured
  • Flexible hoses that are chafed, cracked, bulging or twisted
  • Any leak of brake fluid from pipes, hoses, calipers or the master cylinder

Brake pipe corrosion is a common fail on older cars around Deal, Dover and Folkestone, where sea air and winter salt get to work underneath.

Warning lights and the pedal

  • A brake fluid or brake system warning light showing a fault
  • An ABS warning light that stays on, or does not light at all at start-up. See our guide to the ABS warning light.
  • An electronic parking brake showing a malfunction
  • A pedal that travels too far, feels spongy or sinks under pressure
  • A brake servo that does not assist properly

Checks you can do before the test

  1. Look at the brake fluid reservoir level with the car on level ground.
  2. Look through the wheel spokes at the pads and discs for obvious wear or deep grooves.
  3. On a quiet road, check the car brakes in a straight line without pulling.
  4. Check the handbrake holds the car on a slope.
  5. Start the car and check all brake and ABS lights go out.
  6. Listen for grinding or scraping.

Never get under a car that is only supported on a jack. For a thorough look, a pre-MOT check is quicker and safer. If you have already failed, read failed your MOT, what next.

How we can help

We do not carry out MOT tests, but we do pre-MOT checks and brake repairs at your home or workplace across East Kent. We inspect pads, discs, calipers, hoses and pipes, check fluid, read ABS and brake fault codes, and replace pads, discs and brake fluid on the driveway in most cases. Labour is £30 to £50 per hour, and we always quote before work starts. Send your reg, or a photo of your MOT failure sheet, on WhatsApp 07563 350335 or use our contact page.

Want to pass your MOT first time?

Message us on WhatsApp with your reg and postcode, or use our contact form, for a price before any work starts.

WhatsApp for a free quote Call 07563 350335 Contact form

Labour £30 to £50 per hour depending on the job. Send your reg number and we will reply with a price before any work starts.

Frequently asked questions

Do lipped brake discs fail an MOT?

A lip on its own is not usually a failure. The tester looks at whether the disc is excessively worn, scored, cracked or insecure, and a disc nearing its limit is often given as an advisory.

Will a brake warning light fail the MOT?

Yes. A brake system warning light that shows a fault, including an ABS or electronic parking brake warning, is an MOT failure.

Can I drive my car if it fails the MOT on brakes?

If a fault is classed as dangerous, you must not drive the car until it is repaired. For a major fault, you may only drive it if the previous MOT is still valid, but the car must still be roadworthy, so it is best to get it fixed first.

Is low brake fluid an MOT fail?

Fluid below the minimum mark is recorded by the tester, and it often points to worn pads or a leak. Leaks themselves are a failure, so find out why the level is low.

Sources

Back to Blog